Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Blog Article
How do you really feel when it comes to How to Install a Bathtub?
Mounting a bathtub isn't exactly brain surgery, but it does need solid plumbing, woodworking, and occasionally, tiling skills. Replacing an old bathtub with a new one is additionally a reasonably difficult job. If the old tub is easily obtainable, the project can move easily; if you have to open a wall to eliminate the old bathtub and position the new tub, the task is a lot harder. In either situation, the job is within a residence handyman's skills, although you will need a helper to leave the old tub as well as set in the brand-new one. Make sure you have actually certified yourself for the job and also fit trying it. Instead of employing a service provider to take control of a halfway-completed task, it is far better to consider employing one prior to you start. Chances are you might require a specialist plumber to make tube connections.
This short article will assist you set up a new tub in your restroom if you have already purchased a brand-new tub as well as do not need to transform the arrangement of your previous water supply pipelines.
Your tools as well as product checklist must consist of the following:
Getting ready for the Installment
Firstly, the sustaining frame provided with the bathroom needs to be fitted (if required) according to the maker's instructions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is essential to make certain that if the faucet features a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets device to stop strain on the bathtub.
Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you use every one of the supplied washing machines.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath must currently be ready to be suited its final position.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installation, after that the first thing you need to do is disconnect the water system. After doing so, switch on the faucets to drain pipes any water remaining in the system. The procedure of removing the existing taps can be quite problematic due to the limited access that is usually the instance.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the faucets. Have a fabric all set for the staying water that will certainly originate from the pipes. Once the supply pipelines have actually been eliminated, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from turning throughout this procedure. Once the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Before moving on to fit the new taps, compare the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Setting up the Bath tub
Using the two wooden boards under its feet, place the bathtub in the called for placement. The wooden boards are valuable in uniformly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto four little factors.
The following goal is to guarantee that the tub is leveled all round. This can be attained by examining the spirit level and adjusting the feet on the bathtub until the level reads degree.
To install taps, fit the bottom of the furthest versatile faucet connector to the proper supply pipeline by making a compression sign up with; after that do the very same for the other faucet.
Activate the water supply and also inspect all joints and new pipework for leakages as well as tighten them if required. Fill up the bathtub and likewise inspect the overflow outlet as well as the normal outlet for leaks.
Ultimately, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling as well as securing around the bathtub should wait till the bathtub has been utilized at the very least once as this will certainly resolve it right into its final setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic adapter to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end gives a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly need reducing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, position the faucet in the mounting hole in the bath/basin guaranteeing that the washers remain in location between the tap as well as the sink. Safeguard the tap in place with the maker provided backnut. As soon as the tap is securely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal faucet adapters. The former kind ought to be connected to the faucet finishes initially, tightening up just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the area where the bath meets the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to break a stiff seal, creating the water to permeate the wall surface in between the bathroom and the tiling, resulting in issues with wetness as well as possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to blend in your fixtures and also installations. They are offered in tubes as well as cartridges, and are capable of securing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill the bath tub with water before sealing, to enable the activity experienced when the bathtub is in usage. The sealant can break rather very early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally quickly readily available on the market. It is advisable to fit the ceramic tiles utilizing waterproof or waterproof glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am very excited about How to Install a Bathtub Yourself and I hope you enjoyed reading our article. Sharing is nice. You never know, you will be doing someone a favor. Thank-you for taking the time to read it.
View Website Report this page